Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

Applications and Technologies of All-Solid State Blue Laser

1 Introduction Along with the matureness of laser diode (LD) manufacturing technology, the performance of LD has been improved greatly since 1980s, so various kinds of laser devices based on LD have been developed rapidly, especially the all-solid state lasers. After early experiments and researches, the all-solid state lasers have been commercialized successfully.     

A new detection algorithm (NDA) based on fuzzy cellular neural networks for white blood cell detection.

White blood cell detection is one of the most basic and key steps in the automatic recognition system of white blood cells in microscopic blood images. Its accuracy and stability greatly affect the operating speed and recognition accuracy of the whole system. But there are only a few methods available for cell detection or segmentation due to the complexity of the microscopic images. This paper focuses on this issue. Based on the detailed analysis of the existing two methods--threshold segmentation followed by mathematical morphology (TSMM), and the fuzzy logic method--a new detection algorithm (NDA) based on fuzzy cellular neural networks is proposed. NDA combines the advantages of TSMM and the fuzzy logic method, and overcomes their drawbacks. With NDA, we can detect almost all white blood cells, and the contour of each detected cell is nearly complete. Its adaptability is strong and the running speed is expected to be comparatively high due to the easy hardware implementation of FCN. Experimental results show good performance.     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

三网互联的几个关键技术

对三网互联的几个关键技术进行分析与研究，介绍利用IP技术解决有线电视网地址选择问题，探讨怎样将ATM技术与IP技术相互融合，使真正的信息高速公路成为现实，阐述利用H．323标准全面解决视频网络方案。     

Throughput analysis for multicast switches with multiple input queues

This letter analyzes the saturated throughput for multicast switches with multiple input queues per input port. Under the assumptions of a Poisson uniform traffic model and random packet scheduling policy, we derive the multicast switch saturated throughput under different fanouts. To verify the analysis, extensive simulations are conducted with different switch sizes and fanouts. It is shown that the theoretical analysis and the simulation results have a discrepancy less than 1.9%. Results from this letter can be used as a guidance to design the optimal queuing for multicast switches.     

6σ设计水平的评价

在介绍6σ设计概念和目标的基础上，给出设计水平与百万机会缺陷数(DPMO)关系的计算表达式和关系曲线，并开发了计算机模块，能自动计算与不同设计水平对应的DPMO值，也可以根据实际的DPMO值，自动评价达到的设计水平。     

射频电缆组件组装工艺浅谈

近年来国内外射频电缆组件的发展很快,射频电缆组件的性能不断提高,对射频电缆组件组装工艺也提出了更高的要求.射频电缆组件组装过程多是手工操作,产品的一致性及性能很难控制,要求有良好的工艺保证,为此介绍了射频电缆组件组装工艺,包括电缆的裁剪及剥皮、内导体的连接、外导体的连接和电气性能的测试;探讨了在组装过程中应注意的问题,以及针对内导体焊接易出现虚焊问题进行研究.     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％